The 10 Most Scariest Things About Boarding Up A Doorway

boarding up property Up a Doorway

Boarding up a doorway keeps hail, snow and rain from further destroying the property. It also helps keep scavengers, vandals and squatters away.

Doors are more secure than Windows However, they can be broken or kicked. They must be paired with sturdy door frames made of composite material that won't deteriorate over time.

Take a look at the Doorway

A doorway is an opening through which you go in or out of the room, building or an entry point. A doorway could be a portal which allows access to a different location like a different room in the house boarding up service or another part of the country.

You'll have to measure the doorway. Start by measuring the width of one side of the frame to the other with a tape measure. Before taking this measurement, it is essential to take out all brickmould and trim pieces. This will ensure that you are only measuring the frame and not the actual windows or doors. Make the most of these measurements to determine the dimensions of the doorway.

Take a rough measurement of the opening of the current door if you are planning to replace it. This can be done without removing the old door by prying the old one away from the jamb using an oversized pry tool. This will expose the framing rough which will be used to hang the new door. The height of the rough opening should be measured three times, and the smallest number will be the size of the door you want to install.

You can also determine the width of the doorway by running the tape through the edges of the frame in three spots such as left, center, and right - and recording the largest measurement as the width of the doorway. This is the best way to ensure that your wood will cover the entire area and allow you to build the door or window you want to replace.

Measure the Frame

You can add a sense of security to your home by boarding up windows, doors and other openings that let in the elements. Begin by carefully examining each window to determine the dimensions and shape. Then, you can measure the width of its frame. Note every measurement to ensure that you cut the plywood boards accurately.

Before you begin, put on protective gear to protect yourself from broken glass and other dangers. Also, it's best to work with a partner in order to handle large sheets of plywood is more efficient with a second pair of hands.

Use wide masking tape to seal the cracks and then remove any panes that aren't taped. Cover the remaining cracks with heavy plastic garbage bags. You can also cover the trash bags inside out to increase their strength.

If the frame is good and sturdy, you can cut down on time by putting a new stud across the gap that is in the middle of the window. This will give the frame more strength, without the additional effort of removing and installing the framing itself.

Purchase a few sheets of plywood, and tools like drill, hammer and saw (if cutting is required). Based on the frame's dimensions and marking each board with its corresponding window number. Attach the frame to the plywood by drilling pilot holes using the holes you made earlier.

Take a look at the Jambs

The jambs are the three pieces of wood on which the door is directly mounted. They're crucial in keeping a door closed properly and should be snug and level. If the jambs in place aren't, it's time to make adjustments.

Begin with the side jambs on the hinge. They have a raised section towards the center, referred to as a doorstop. The doorstop rests on the door slab to stop it from hitting the frame when it closes. Attach a piece or plywood on the bottom of each stud to raise the floor in the opening by 1/2 inch. (Photo). This will help prevent the door from scraping against the tile, carpet or throw rug when it is shut and opened.

To get an accurate measurement for the hinge side jamb, take off any trim, molding or casing that's attached to it. This will reveal the rough opening so you can accurately measure it.

Note the location of the hinge holes both on the inside and outside of the hinge jamb. Utilizing a combination square find the mortise depth of the hinge and adjust the combination square so that it's the same as the mark you made on the jamb of the hinge. This will ensure that the hinge is placed in the frame and aligned to your door. Repeat the procedure on the latch jamb side the door. Make use of a nail gun and 2-1/2-inch finishing screws to secure the strike side.

Take a look at the Header

A header is a heavy dimension lumber board that is nailed to the wall's top framing, which transfers loads above window and door openings to studs below. When properly frame, the king and jack studs are secured to each end of the header. They also butt up against the header at both ends to create solid columns that transfer the weight of the opening to the floor and foundation.

In conventionally framed homes, you can use a set of tables in the code to size the header to fit a certain span. A typical header is a double 2x12 and the code has tables for three widths of a building and you can use interpolation to get the next wider size to get the appropriate header size.

But there are other, more efficient alternatives to the standard 2x12 header that can reduce the need for lumber, decrease thermal bridging and free up space for insulation. Builder Mike Guertin takes a look at these options and when they're suitable:

He also explains the rim-board headers that bridge an opening without using the use of a header. This removes an additional step in framing process, and can result in stronger frames. He also discusses box headers, which are more difficult to build however, they offer larger spans than single-ply. He also explains the fastening schedule for these headers that calls for common nails of 8d spaced every 3 in.

Cut the Boards

It is important to clean the space thoroughly prior to making a boarding plan for an entranceway. To make enough room for work and prevent damage to your possessions, take down all furniture and décor. Detach the doorknobs and locks and keep them in a safe location for later reinstallation. To improve adhesion, clean the frame and door and clean the entire surface to remove dirt and dust. If needed you need to sand rough areas to ensure that the boards fit properly and offer effective protection.

Once the doorway is clear, it is time to start cutting the plywood boards. A circular saw can cut straight lines through wood and cut easily through it, whereas a Jigsaw is more suitable for areas that are curving. Wearing protective equipment like safety goggles and a dust mask, is essential during this step.

When the board has been cut to size, it is essential to ensure that it is aligned with the frame and jambs. To strengthen the board, it's an excellent idea to add some vertical pieces to the bottom of the board. Once the board is properly aligned and secured it is now ready to be nailed into the correct position.

boarding up commercial property up a doorway can help protect the property or home from harm and unauthorized entry during a storm, disaster or other event. It can also be used to protect vacant properties or prevent theft and break-ins until the property is used. Carefully evaluating the situation and the reason of the emergency boarding up service up will help to guide the material selection and the method of installation for the most effective results.

Install the Boards

Instead of nailing Instead, use strong screws to secure the boards. These fasteners are strong and resist the pull of prying. This improves the effectiveness of your board. Caulk or weatherstripping can be used to close the edges and prevent rain and wind from getting in through the gaps. It's also a good idea to leave a ventilation gap to avoid humid air and stuffy air.

If you're using a power drill, make sure to wear gloves and goggles to protect yourself. Mark your cuts using the aid of a straightedge and pencil because mistakes are more difficult to rectify after cutting. You'll need to make the cuts as precise as you can so that the boards fit perfectly against the frame and door casing. The jambs and head must be cut so that they are aligned with the wall.

It is recommended to prepare your home before the storm hits so that you will have plenty of time to board up other areas that are vulnerable. A little planning can save you a lot of time and help you prepare your business or home for the possibility of a disaster. With the right preparation your home or business will be safe from criminal activity and damage caused by flying debris and winds. It will also give you peace of mind knowing that your property is safe from damage.