9 Things Your Parents Teach You About Patio Door Lock Repair

Patio Door Lock Repairs

Over time, wear and tear could cause lock malfunctions. However, there are simple and effective ways to restore your uPVC patio door lock repair (diggerslist.com) door's security.

These quick fixes will make your home safer regardless of whether you re-align the lock or clean the locking mechanism.

Clean the Lock

While patio doors are a great way to let in the outside and keep the elements out, they can also be an issue for security when your lock isn't functioning as it should. Over time wear and tear, hot and cold weather dirt and debris can take their toll on your patio door's lock and make it difficult to open. With a little attention you can ensure that your lock for your patio door always works correctly.

It is important to first clean the patio door lock and all moving parts. This helps to get rid of any grime and coatings that could be preventing the lock from functioning as it should. Start by wiping all the moving parts of your patio door lock using a wet cloth. Then you can use a scouring paper or rough damp cloth to scrub the dirt-infested areas of the door frame and frame. Then clean the lock using a dry towel to remove any remaining moisture. Let it air dry before you use it.

If you have an exterior door that is fitted with a pin tumbler latch mechanism, you can grease the lock by applying powdered graphite to the key or using a Teflon-based lubricant such as WD-40 Multi-Use Product. This kind of lubricant is easy to apply, and it doesn't dissolve with time. If you're unable find the right lubricant to use with your lock, use a pencil with larger tip. Put the pencil in the lock, and shake it around to distribute the graphite.

Regular maintenance is also required to keep the tracks of sliding patio doors clear from dirt, dust and debris. These tracks are especially susceptible to snow, ice and other particles, which could cause them to jam or bind. This can make it difficult for your patio door to open and shut.

Tracks for sliding glass patio doors repair patio doors and rollers can be cleaned by removing any damaged or dirty weather stripping, cleaning them, then replacing it. The same is true for patio door rollers, which can be cleaned and sprayed with non-stick lubricant in order to allow them to move freely.

Lubricate the Moving Parts

uPVC French doors, like sliding patios, are operated by using 3 to 4 or sometimes 5 point locking mechanisms. This includes the lock cylinder and handle that is operated by keys. These doors also require maintenance, specifically lubrication on the moving parts. This can be done with a thin oil (never WD40) and should be done once per year.

If hinges that are sagging don't cause the problem, it could be that the door isn't aligned. It could be rubbing or catching against the strike plate's opening in the frame. The solution is how to repair tilt and slide patio door remove the strike plate, and then use an abrasive chisel, which will enlarge the mortise that it rests in. This allows the latch to fit perfectly in the hole, and also prevents scratching or catching on the frame.

While the cylinder is out of the way, measure its width with an object or a piece of wood that will fit in the adjustment screw gap above the lock. The outer dimension is measured from the outside of door to the center of cylinder. The inner dimension is measured from the center adjustment screw to the end of the of the cylinder.

Check the width of the lock.

If your patio doors repairs near me door latch is difficult to turn even after cleaning and lubricating, it's possible that it's out of alignment with the strike plate hole. Verify that the door is balanced, and if the hinge screws are secure. In a lot of cases, moving the strike plate downwards or upwards could fix the problem.

The most common issue is when the lock's strike is too small for the latch to properly engage. In this case, enlarge the opening using the hammer and chisel. Then test the latch to ensure it does not rub against the jamb frame of the door or fall on it.

You should identify the type mortise lock you have before buying the replacement. This can be done by looking at the faceplate and noting whether it is square or round. Examine each screw hole on the current lock, and note their size. This will enable you to locate a replacement lock that is exactly the same width and will fit in the hole that you already have.

In addition to identifying the mortise lock that is currently in use, you'll also want to inspect it for any scratches or bends that might require repair. A badly bent or damaged latch is more likely than one that has frequently used to break. Replace the lock if it shows evidence of damage.

After you've determined the type of lock replacement you need Now it's time to begin the actual repair. Remove the old handle and spindle out of your patio door, and then install the new one. Begin by installing the handle in the interior, aligning it with the spindle and then fixing it with the two screws or bolts that hold it. Once the handle's interior is installed, put in the handle on the outside and screw it in place, too. After you've completed these steps check the handles to make sure they open and shut easily and that the latch is in contact correctly with the strikeplate.

Check the door's Strike

The strike plate and door latch are two components which work together to secure the door. If they are not aligned properly, the latch won't latch the door properly. Fortunately, this problem is usually easy to correct.

Check the receiving holes of the strike plate to ensure they are clear of obstructions, such as dirt or plastic plugs. Then, loosen the keeper screws that hold the strike plate in place and allow it to move vertically, but not removing it from the frame of the door. Then, adjust the strike plate until its receiving holes align with the latch hooks on the door latch. After the strike plate has been adjusted then tighten the screws and then test the door to determine whether it shuts easily with the new adjustment.

Door strike plates can be a bit difficult to locate for homeowners with sliding patio doors, but they're crucial to lock and unlock your door. The metal plates are typically located on the top and bottom of the door jamb, where they serve as the door's latch. Then, the door latch is placed on the strike plate to create a seal when closed. If the strike plate is damaged, rusted, or not installed correctly, it can prevent the latch from locking the door securely.

The most common reason for the patio door lock to not close or not close is a misalignment between the latch and strike plate. The most effective way to test for this is to perform the "lipstick test." Rub some lipstick along the edge of the deadbolt, and then put masking tape on it. The lipstick will leave an impression when you close the door. This will indicate exactly where the latch joins the strike plate. If the mark is too low or high you can easily adjust the strike plate.

Locks for sliding patio doors help protect your home from intruders, and if they're not working correctly, you must repair the issue quickly. By following these simple steps, you can repair your patio door's lock and get it back to normal in no time.